|
|
|
|
1994 – 2013 DODGE RAM 1500 2500 3500 |
1994-2013 Contrivance RAM 1500/2500/3500 |
1994 – 2013 DODGE RAM 1500/2500/3500 HIGH CLEARANCE CONTROL Artillery for Stock to vii” LIFT – $399.95 |
Stryker Off Road Designs’ DOM (Drawn Over Mandrel) Control Arms!
These are
CAD designed craftsmanWelded
made command arms. They are designed to fit the front of a Dodge Ram 1500 2500 3500 4×4 with Stock to vii” lift height. These WILL fit the 1500 Megacab 4×4 as well.
This is for a set of 4, includes 2 uppers and 2 lowers. They definitely allow the best tire fitment as it re-centers the axle in the cycle well. These are sold in a gear up of four, because you lot really need uppers AND lowers to re-center your axle properly.If you’ve installed a leveling kit, you DEFINITELY demand longer control artillery! This is because as you lot lift the truck, the angle on the artillery increases, pulling it back in the wheel well.
If you lot’ve installed a two-3″ leveling kit or a lift kit and your front tires are close to rubbing the fenders near your doors, yous demand longer arms to properly re-centre your axle!
|
Our ARMS areguaranteed to perfectly fit your year model truck (twelvemonth models have different sizes of hardware, requiring unlike inner bore sleeves for optimal fitment).
Some competitors salvage cost past designing merely 1 size and selling y’all a kit full of spacers, shims or washers for you to make up for their reduced investment in your model truck.
Some lower cost competitors may also utilise cheaper rolled sleeves with a seem can carve up autonomously, due to stress from movement (run into comparison images), shredding your bushings from within! Many competitors even uselower price Rubber Bushings. These arms are precisely the proper length to center your front beam within the cycle well at stock to 1 1/two”, 2-iii”, 3 1/12″ to five” and 5 ane/2″ to 7″ lift top – Each arm is jig-congenital, using precisely measured materials, and is inspected before beingness shipped. Buy with conviction! That’s correct, Stryker designs and manufacturers a Made control arm to match your truck.In OUR earth of Rugged StyleONE SIZE DOES Not FIT ALL TRUCKS! |
|
Stryker isconfident in offering you aLIFETIME WARRANTY on our Fabricated command Arms because the Quality of theEngineered Design,Materials used,Manufacturing Process,Finishing andConcluding InspectionWARRANT 1!
|
This is an case of a
Mopar OEM replacement control arm. Stryker design engineers saw room for comeback and designed both our Drawn Over Mandrel (DOM) and our NEW
Fabricated
High Clearance
arms every bit a true Dodge 1500 2500 3500 Heavy Duty upgraded Command Arm.
Stryker’s DOM Control Arms
Our heavy wall (Fatigued Over Mandrel)
DOM
sleeves are application specific, and guaranteed to perfectly fit your twelvemonth model truck (year models take dissimilar sizes of hardware, requiring different inner diameter sleeves for optimal fitment).These artillery are precisely the proper length to center your front axle within the wheel well – Each arm is jig-built, using precisely measured materials, and is inspected earlier being shipped. Purchase with conviction!These artillery are precisely the proper length to center your forepart axle within the bicycle well!
Stryker’s Loftier CLEARANCE DOM Control Arms
Our heavy wall (Fatigued Over Mandrel)Loftier CLEARANCE
DOM
sleeves share all of the same features and benefits every bit our straight arms but with the added do good of
High Clearance Control Arms
forless Tire Rub and IMPROVED TURNING RADIUS. Theyare
Too application specific, and guaranteed to perfectly fit your year model truck (year models have different sizes of hardware, requiring different inner diameter sleeves for optimal fitment).
Fabricated High Clearance Control Arms
for less Tire Rub and IMPROVED TURNING RADIUS!
These are make new
ane/4″ steel structure,
CAD designed, and
plasma cut
fabricated command artillery for the front of a
Dodge Ram 1500 2500 3500 4×4 with ii-3″ elevator acme.
ThisI-Axle Fabrication is the image of Stryker’southward delivery toRUGGED Mode!These Will fit the 1500 Megacab 4×4 as well. This is for a set of four, includes 2 uppers and 2 lowers.
If a
couple more than degrees of turning radius
and
less Tire Rub
captures your attention, you lot should really consider a
Loftier CLEARANCE control arm
for your Heavy Duty 1500, 2500 or 3500. And
Stryker
considers our Brand New
Fabricated High Clearance Arms
a significant offering consistent with our goal of providing you lot with
Rugged Style!
Benefits:
-
LIFETIME Replacement Warranty!
(excludes powder coat) - Properly centers front axle within wheel well
- Stronger than manufactory stamped steel artillery
- Beefy tubular steel construction due west/ DOM collars
-
Stryker’southward Craftsman Weldersbuild these in HOUSE here in Marysville, TN!
- Daystar brand PTMEG poly bushings
- Year-model-specific DOM sleeves
- Greasable 1/4″ screw-in zerk fittings
- Made in the USA!
Kit Contents:
(ii) Upper Command Arms
(two) Lower Control Artillery
Technical Notes:
Does not fit 2002 or newer 1500 models
Re-uses factory hardware
Aircraft Note:
Zerk fittings no longer come pre-installed in lodge to reduce the hazard of damage during transit
Custom Colors:
Custom colors are bachelor for an additional fee. We use Prismatic Powders, and so delight visit theirwebsiteto select your color, and note the color code at checkout. Custom colors volition delay the ship appointment, on average, by 2 weeks.
Source: https://strykerordesign.com/products/dodge-ram-1500-2500-3500-control-arms
